The Easiest Way to Reset a Car Alarm That You Must Try
A car alarm is a device used for vehicles as part of a security system. Car alarms were created to make it easier for car owners to operate their vehicles, for example locking and unlocking doors.
In today's modern era, just by pressing the button on the alarm, you can even control various vehicles at once. Not only that, a car alarm can also prevent theft because it is equipped with a theft security system.
Therefore, its existence is very important. If you have a car alarm, don't let it break, let alone lose it.
However, if your car alarm is having problems, one way to fix it is to reset it. You can see how to reset a car alarm in the following explanation.
the Easiest Way to Reset a Car Alarm
Car alarms sounding themselves for no reason are often a problem, because they can cause noise and annoy people around you. To solve this problem, you need to reset the car alarm so that it can return to normal.
Reset a car alarm is not as difficult as you might think. There are several ways to reset a car alarm remote that can be done. Here's a full review of the easiest way to reset a car alarm.
1. Make Sure the Remote Battery Is in Good Condition
Confirming the condition of the remote battery is the first thing to do. If the remote battery is low, replace it immediately.
Because, if the remote battery runs low, it will affect the remote 's performance. for example it is difficult to open the door, the signal range is lost, until the alarm sounds itself.
2. Open the Car Door Manually
To stop the loud and annoying sound of the alarm, open the car door manually. After that, close the door tightly. The alarm that sounds is caused by the door not closing tightly.
3. Open the Door on the Right
After making sure all the doors are tightly closed, the next way is to open the right door. Then, leave the door open to continue the reset process.
4. Check the Alarm Indicator
Try to check the alarm indicator. If the indicator lights up, it means you have to make sure the door is tightly closed and locked. Usually, the alarm system and the alarm indicator will light up if one of the doors is not closed tightly.
5. Insert the Car Key into the Keyhole and Turn It to the on Position
After that, insert the car key into the keyhole to start the car engine. Then, turn the car key to the On position and press and hold the lock button for five to ten seconds.
6. Turn the Key to the off Position
After that, release the lock button and turn the car key to the Off position. Then, turn the key back to the On position.
7. Press and Hold the lock Button
Next, press and hold the lock button for five to ten seconds. Do this repeatedly until the alarm indicator light on the dashboard turns off.
8. Take Out the Car Key and Retest the remote
When the indicator light is completely off, take out the car key and get out of the cab.
9. Close All Doors and Lock the Car
Close all doors and lock the car using the lock button on the remote to ensure the remote is functioning properly.
10. Make Sure the remote Frequency Is Not Disturbed
If there is still a problem with the car alarm remote, try to check the remote frequency is not disturbed. The trick is to avoid locations full of electromagnetic waves so that component performance can return to normal.
the Cause of the Car Alarm Error and Needs to Be Reset
Car alarms are very important to avoid theft or other harmful things. When you lock the car, the alarm will sound and the door will simultaneously lock.
After all the doors are locked, the alarm will activate to protect the car from major vibrations. The car engine cannot be started when the alarm is in active mode.
However, what if the alarm doesn't go off? When the alarm you are using doesn't sound, before resetting or replacing the remote alarm, it's a good idea to first identify the cause of the car alarm error and need to be reset. Because, there are several reasons why the car alarm does not sound.
1. Often Fall
The main cause of the car alarm remote not working properly is because it is often dropped. As with other things, if the remote alarm is dropped frequently, it can cause the components in it to be shifted or detached.
Therefore, save and take good care of the remote alarm. Do not fall, especially falling from a high position. Because, it is possible that the remote alarm will be destroyed due to the impact of a hard object under it.
2. Too Often Stored in Pants Pocket
In addition to frequent falls, it turns out that too often stored in a trouser pocket is also the cause of the car alarm remote not working. Moreover, the pants used are tight pants.
This can make the remote become depressed when it is in the pocket. If the remote is accidentally pressed continuously, the buttons on the remote will be damaged more quickly.
It's a good idea to keep the car alarm remote in your pocket to avoid accidentally pressing the remote. If necessary, store in a bag.
3. Experiencing a Short Circuit
The next cause is a short circuit in the car alarm remote. A remote that is frequently pressed on purpose can cause a short circuit.
Not only that, the remote that is exposed to water can also experience a short circuit. Because basically, all electronic objects when exposed to water will definitely experience a short circuit.
To overcome this, you should store the remote in a place where the remote cannot be stressed and keep the remote away from places where there is water.
4. Sensitivity of Alarm Sensor Is Very Good
Having a car alarm remote that has a high sensor sensitivity is great, but it can make the car sound continuously when there is something that can threaten the existence of the car. For example, when it rains heavily accompanied by lightning, animals accidentally bump into tires or car bodies. there is even a subtle shock caused by other vehicles.
If that's the case, you need to check the alarm indicator to identify where the error occurred. It could be that the sensitive alarm sensor is damaged or there is an error during installation.
Car Alarm Functions and Benefits
Along with advances in technology, the alarm function is also experiencing development. Almost all cars have been equipped with an alarm system that has an important role.
There are various functions and benefits that can be obtained from using a car alarm remote. Especially with regards to security. Check out the following information to find out the functions and benefits of car alarms.
1. Prevent Theft
The first function is to prevent theft. As we have seen, car alarms are related to security.
This is because the alarm is able to complicate the crime when committing theft. The loud sound of the alarm and the flashing of the turn signal can attract the attention of those around you, so that you will quickly recognize the danger signs in your car.
2. Warning Sign
A car equipped with an alarm can give a warning sign when there is danger, for example the car you are driving almost hits an object. Automatically, an alarm will sound to signal that there is an object in front of you.
Not only large objects, even small objects can be detected because of the sensitivity of the sensor in the alarm.
3. Become a Security System
Apart from preventing theft, the alarm also functions as another security system. When a car is broken into or tampered with, an alarm that sounds will serve as a warning.
The alarm has a touch sensor and a warning sensor, so it will sound if there is suspicious activity on your car, such as opening a car door that cannot be opened that you try to do by force. In addition, the alarm will also sound automatically if there is an indication of a fire, such as a short circuit or the appearance of a spark.
4. Locating the Car
A car key that has been installed with a remote control can make it easier to find your car when parked in a public place. The remote alarm has four buttons, namely to open the door, lock the door, open the trunk door, and for the alarm.
If you park your car in a public parking lot or in a crowded place and it's hard to find a car, you can use a car alarm remote. With a car alarm remote. you can find the whereabouts of the car.
Moreover, now remote car alarms can be controlled via a smartphone. This makes it easier for you to track and control the car.
Components and How the Car Alarm Works
Some people do not know the components and how the car alarm works. In fact, in general, the components attached to a car alarm use a simple device.
There are three main components embedded in a car alarm, namely sensors, control units. and sirens. These three components are interconnected with each other. See a more complete explanation below.
1. Sensor
There are several sensors that are connected to a number of car parts, especially car doors. These sensors have been designed in such a way to detect any suspicious activity.
When the sensor detects suspicious activity or shock, the alarm sensor will work by sending a signal to the control unit. After that, the control unit will activate the siren, so that the alarm sounds and invites people's attention.
In addition, there is also a microphone or pressure sensor that will send a signal to the control unit when it detects a sound level that is not too loud, so it can be a sign of theft.
2. Control Unit
The signals that are captured through the sensor, will be sent to the control unit. Later, the system will activate outputs. such as sirens or flashing lights as a sign of a car alarm.
This control unit system generally uses a radio wave transmitter. So, if the control unit component has a problem, the alarm can sound itself.
3. Siren and Flashing Lights
The sound produced by sirens is often perceived as distracting, although its performance can help provide a signal.
The siren relies on transmitting the captured signal via sensors at the command of the control unit. which then activates the output by emitting a sound and flashing lights. The two outputs are the warning signs if something happens.
How to Set a Car Alarm
When you already know the ins and outs of a car alarm, you can start installing the alarm independently. How to install a car alarm is not too difficult. Even so, you still have to be extra careful because there are several things that need to be considered when installing a car alarm.
If there is an error in the installation, the alarm cannot be used or will not function normally. For that, let's look at the steps on how to install the following car alarm.
1. Selection of central Lock and Alarm
As a first step to installing a car alarm, you need to choose a central lock that matches the type of car so that the alarm can function properly.
Generally, in one central lock package consists of 4 actuator guns or lock actuators. 4 pull and push wire rods, 1 set of cables for 4 doors, and 1 central lock module with 8 connector points.
After making sure the central lock component is complete, you must pay attention to the placement of the alarm according to the type of car, electrical installation, to the power source that will be used by the alarm. When everything is ready, you can start installing the car alarm.
During installation, it is highly recommended that you follow the wiring diagram. A wiring diagram is a simple working drawing that shows the installation circuit that must be followed.
However, if you are used to car alarms, you can ignore the wiring diagram.
2. Install the Default Cable for central Lock and Alarm
The next step in installing a car alarm is to drill the inside of the door as a place to place the lock actuator.
The component consists of 5 wires with different colors, namely black, white, brown, blue, and green. The cables can be installed in the driver's door and other doors.
After that, attach the central lock default cable according to its part on the lock actuator module. We recommend placing the lock actuator module under the dashboard so that the module is protected. If the default central lock cable has been installed, you can start assembling the car alarm.
The trick, connect the power cable on the lock actuator module to the battery ( battery ). When finished, check the lock actuator on the main door by raising and lowering the door lock lever.
If the installation is correct, the lock actuator on the other door will follow, both when the door lock lever is raised or lowered.
3. Connect the central Lock and remote Alarm
The last way to install a car alarm is to connect the central lock to the car alarm remote.
In connecting the central lock with the remote alarm, you have to really pay attention to the cable connection. Because, these cables must match the path on each alarm in order to work using the remote.
Connect the red wire on the car battery to the positive (+) pole, then the black wire is connected to the car body or the negative (-) pole. Connect the brown wire to the right and left turn signal lights, while the pink wire is connected to the built-in speaker or alarm siren.
The red and black wire is usually connected to the trunk, but is rarely used. Make sure all cables are connected and glued to the alarm device, then install it under the dashboard.
Tips for Choosing a Good Car Alarm
Each car alarm has its own advantages and defense systems. Moreover, the default car alarm is standard.
In this day and age, criminals on vehicles have become 'literate' to universal car alarm schemes. The perpetrators can even easily cut the cable and avoid warning alarms.
For that, it's a good idea to choose a good car alarm by paying attention to the following things.
1. Match Car Type with Alarm
Not all car alarm devices are compatible with all types of cars. If it doesn't match your car type, the remote alarm won't work.
Therefore, first match the type of car with the car alarm that you will use. That way, the alarm can function properly.
2. Know the Signal Capture Power
Before buying a car alarm, you should first know the capture power of the alarm signal. How far can the alarm catch the remote control signal ? This needs to be considered because it can make it easier for you to turn on or turn off the alarm remotely.
3. Has a Gps tracker Feature
A good car alarm has a GPS Tracker feature in it, this GPS Tracker can later be connected to a smartphone. so you can control it from your cellphone.
4. Has a keyless Feature
In addition to the GPS Tracker feature. a good car alarm also has a keyless feature. This feature allows you to lock and unlock the door with just one button. So, you don't really need a key. Very practical, right?
5. There Is a way Pager Feature
This way pager feature can help you monitor the car remotely. With the way pager. you can receive an alert when the alarm sounds.
The warning is usually a vibration, sound, or visual. In addition, through the way pager you can provide feedback regarding the next action.
6. Has a High/shock Sensor
Choose a car alarm with a high/shock sensor, up to a motion detector. This shock sensor is designed to trigger an alarm in light and heavy shocks. That is, regardless of the level of shock, the car alarm will give a warning.
To be more effective against vibration or shock, you can use dual shock zone sensor protection.
7. Can Connect with smartphone
Increasingly sophisticated technology makes several electronic objects can be connected to smartphones, one of which is a car alarm. As is known, the remote alarm can only reach a distance of 500 meters to 1 mile.
If the remote alarm is connected to a smartphone. you can control it remotely. However, it depends on the signal strength of your smartphone.
8. Make Sure the Alarm Has a Warranty
To avoid the risk of loss due to the alarm not functioning properly, it's a good idea to choose a car alarm that has a warranty. Also pay attention to how long the manufacturer provides the warranty. The longer the warranty, the better the quality.
Not only do you need to make sure that your alarm has a guarantee for damage and loss protection, you also need to have car insurance as a form of protection for your vehicle.
If you are looking for the best vehicle insurance. of course Auto Insurance Agencies is the answer. You can freely search for types of insurance according to your needs and abilities.
